Nevada Les Paul

A few months ago I spotted this really sexy looking beast of a guitar on Ebay. It was some sort of cheap chinese Black Gibson ES175 clone. With three humbucker sized P90s and a Bigsby B6. I put in a lowball bid and failed to win it. But as time went on I kept thinking about it. Even though it was pretty beat up and had electrical tape all over it, it was still a very striking guitar.






Then one day as I was thinking about it I was hit with the inspiration to convert my Nevada Les Paul. The Nevada isn't a semi acoustic, but it is the right shape and colour and desperately in need of TLC. The Nevada was a guitar I picked up from the local cash converters for a whim. I hadn't really thought about what I was going to do with it other than do some coil tapping and splitting but restyling it to a carry three p90s and a Bigsby seemed like an fun project.

I ordered three p90 pickups from Vanson guitars on Ebay and a Bigsby B70. For the wiring I had no fixed plan but thought I would try out a 4 pole 11 throw rotary switch. I also managed to get old of an old soviet military 5 pole 11 throw switch which would allow me ultimate freedom, but unfortunately was too big to fit in the body.

I thought the main challenge would be cutting a hole for the middle pickup but in the end it was planning the wiring that would be the hard part. But more on that later.

Cutting the hole for the pickup turned out to be easier than I thought it would be because the guitar isn't solid all the way through. I was able to cut through the arched top just using a dremmel tool. After getting the hole in place all I needed to do was drill two holes in the body for the pickup mounting screws to fit in and there was enough room to fit the pickup.

The other bit of woodwork that needed doing was to fit couple of pieces of dowling into the holes left after removing the stop tailpiece. I left these 24 hours to let the glue dry before attaching the new Bigsby B70 tremelo. The Bigsby conveniently covered the slots so I didn't bother painting them.

I put the dremel to use again to cut the scratch plate to fit three pickups. its not the neatest job but only noticeable close up.

With the guitar all styled out. The next step was to plan the wiring. This turned out to be very challenging. When I wired up the Gretch I only had two pickups to contend with. I'd come up with a clever way of planning the wiring but with only 4 poles on my switch and 6 wires plus a huge number of wiring options for three pickups it wasn't easy.

The 11 way switch combined with phase switches on the volume controls would allow me access to most of the 35 tones that are possible with a 3 pickup guitar . However the type of rotary switch has limitations that means that it is not possible to do every possible combination. Also how do you choose which tones you want easy access to?

There is still a lot of thought that will need to go into the wiring and a little experimentation before I commit to a wiring scheme.

More on the wiring in the next post.

Gretsch G5265 Baritone Switch Replacement

When I started (and abandoned)  this blog over a year ago I thought I would be posting about one of the various project guitars that I have. In particular the nasty Les Paul clone with the crazy sustainer I've been building.

I certainly would never have predicted that my first post would be about a Gretsch Baritone G5265 Jet. The thought of actually owning one never really entered my mind back then let alone the thought of modifying one. Yet here I am.

Its a lovely guitar but it has one rather annoying feature, the three way selector switch. When I'm strumming I frequently knock the switch into the neck position. To be fair its more the fault of my playing style, but when seated its where my hand naturally falls.

So I thought to myself, why not replace it with a a rotary switch instead. Then I thought why have a three way switch when I could have a 6 way switch to give me every combination that you can have with two pickups.
 
I googled around to see if I could find a wiring diagram that would help with some success but the one I found didn't have the selections in the order I wanted. So I decided instead to work it out from first principles.

The approach I took was to draw a schematic for each circuit I wanted to make then I could colour in a block diagram of the switch to show which terminals should be wired together. With the block diagram complete I could apply the colour codes to a representation of the switch. With all the planning in place soldering the switch was as simple as painting by numbers.

Have a look at the embedded slides to see the documentation




When it came to wiring up I used some solid core jumper leads that had sleeves of the right colour. The solid cores made it possible for me to connect everything together before applying the solder so I could double check. There it is on the left looking like the console of the tardis

Once all the wires are soldered in, its simply a case of attaching the wires from the pickups and the controls to the appropriate tabs on the switch.

Identifying the cables wasn't too difficult. You can identify them by looking at how they are attached to the three way switch.  The white cable going to the central contact of the three way switch is hot going down to the controls and jack socket and the other two white wires are for either pickup.

One error I made was that I didn't pre-tin the terminals or the wires. Had I done so, then I wouldn't have had a dead connection on one of the positions. The green jumper had a dry joint that wasn't making contact so position 3 was not working. I had to take the switch out and do some probing with a multi-tester before I worked out what was wrong. To resolve it I just reheated the joint.

The switch came with a chicken head knob, but I thought it looked awful so I bought a Gretsch knob from ebay. I had to dremmel out the hole a little as it didn't fit in the switch shaft very well but once it was on it was a really good fit.

 The switch adds a lot of variety to the sounds and the out of phase settings are pretty unique. Not great dry, but they work well with distortion. There is quite a big different in volume between the settings and I think if I had been able to test out the different settings in advance I might have chosen a different  order. The good news is that the way I have documented the switch connections means that it is trivial to change the layout. I can simply change the order of the columns on my block diagram and its painting by numbers. If I had decided I didn't need six settings I could wire up a 4 way or 5 way switch using the same diagram, just skipping the positions I don't need.

Here we go again,another blog

What is this all about then? Well recently Ive got back into playing guitar. I think I can blame Rocksmith for that and the 25th reunion of my school band. I've also rekindled my passion for modifying guitars.

I bought my first guitar around about 1984. Without any musical skill whatsoever, I joined a band as lead singer, and some short time after that found myself in the Notting Hill music and video exchange. For the princely sum of £60 I  bought a used Kay Electric strat copy. Seen here being played by my friend Nick

Nick Baron and my Kay Electric

This guitar had obviously seen some action. The frets had grooves worn into them by the strings and it was a bit buzzy but otherwise sound. Of course not having a clue about playing guitar I didn't do anything sensible like learn music, take guitar lessons or anything like that. No I got The Guitar Handbook
by Ralph Denyer. I learnt how to dress the frets, set up the action and intonation, added new strings and  adjusted the truss rod. I still couldn't play for toffee, but now the guitar was really nice to play and easy on the fingers.

But it didn't stop there. I added a pre-amplifier that I'd build on perfboard from a circuit diagram in the book and turned one of the tone controls into a gain control. When I was done, the guitar could go from a sweet acoustic tone to sounding like a jumbo jet. I eventually sold it to pay for a squier telecaster for double what I paid for it

Every guitar I have owned has had something done to it and I have been bitten by the bug again. In this blog I'm going to document the crazy stuff I've started doing with my newest guitar